On Mon, 11 Oct 1999, Bernd Walter wrote:
| On Sun, Oct 10, 1999 at 11:55:52PM +0200, Thomas Köllmann wrote:
| > Beide manuals lassen mir mehr Fragen offen, als sie beantworten. Aber
| > ich hätte wohl erwähnen sollen, daß ich sie gelesen habe -- ist wohl
| > nicht selbstverständlich.
| >
| > Weil wir nun dabei sind:
| >
| > PPC(4) FreeBSD Kernel Interfaces Manual
| > [...]
| > PPB_EPP 0x4 /* EPP mode, 32 bit */
| >
| > Obige flags stellen ppc0 auf "EPP mode" ein, ja?
|
| Nope.
| Es handelt sich hierbei um bit 6 - also um die chipset specific detection.
Woher weißt Du das? Die man page sagt:
bit 6: activate IRQ (1 IRQ disabled, 0 IRQ enabled)
Ich hab's noch nicht verstanden, was?
| Bit 0-3 sind auf 0x0 (die letzte Ziffer!) also im Centronics compatible mode.
|
| > Woher kommt die zusätzliche `0' in `0x40' oben? (Ist das `ne sehr
| > blöde Frage?) Und was eigentlich bedeutet das `net', das ich ja durch
|
| In Anbetracht dessen, das jedes Computerbuch auch heute noch als erstes
| die Zahlensysteme erklaert vermutlich schon... [...]
Danke. Hab' nur eins dieser Art gelesen -- Leheys `Complete FreeBSD'.
Ist aber kein `Computerbuch' nach Deiner Definition. Zahlensysteme
sind für Philosophen jedenfalls nicht unbedingt von primärem
Interesse...
| > ppc0 at 0x378 irq 7 on isa
| > ppc0: Winbond chipset (NIBBLE-only) in COMPATIBLE mode
| > lpt0: <generic printer> on ppbus 0
| > lpt0: Interrupt-driven port
| > lpt0: <generic printer> on ppbus 0
| > lpt0: Interrupt-driven port
| >
| > Woher übrigens dieses Echo bei lpt0:?
|
| Das habe ich ehrlich gesagt noch nie gesehen - evtl gibt deine kernelconfig
| darueber aufschluss.
Dies ist von meiner "workstation" - derzeit experimentell, output
stimmt also nicht mehr mit dem obigen überein, "echot" aber immer
noch:
controller ppbus0
device ppc0 at isa? port? flags 0x05 tty irq 7
device lpt0 at ppbus?
Hier die des servers, an dem der Drucker hängt:
controller ppbus0
device ppc0 at isa? port? tty irq 7
device lpt0 at ppbus0
controller ppbus1
device ppc1 at isa? port? tty irq 5
device lpt1 at ppbus1
ppc0 at 0x3bc irq 7 on isa
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppc1 at 0x278 irq 5 on isa
ppc1: Generic chipset (NIBBLE-only) in COMPATIBLE mode
lpt1: <generic printer> on ppbus 1
lpt1: Interrupt-driven port
lpt1: <generic printer> on ppbus 1
lpt1: Interrupt-driven port
Auf beiden Rechnern läuft 3.2-RELEASE.
Könnte es daran liegen, daß die man page die SYNOPSIS mit
controller ppc0 at isa? port? tty irq 7
For one or more PPBUS busses:
controller ppbus at ppc0
angibt, während LINT und GENERIC, wie ich oben,
controller ppbus0
device ppc0 at isa? port? tty irq 7
benutzen? Ich werd's mal probieren...
Gruß
- Thomas
-- She says, "Why are you partial to that Playboy con? When you can see me naked anytime you want?" - The Tragically Hip, The Luxury # PGP key sent on request / PGP key auf Wunsch per e-mail To Unsubscribe: send mail to majordomo(at)de.FreeBSD.org with "unsubscribe de-bsd-questions" in the body of the messageReceived on Mon 11 Oct 1999 - 21:59:17 CEST